The Compression Testing Machine consists of a base plate and steel cross head tightened by tension rods. The hydraulic jack, inside the cover is fixed on the base plate. The lower platen rests centrally on the hydraulic jack.
Model: DCM01
Brand: Mechatronic
Applications: Extensomerter
Industries: Aerospace, Automotive, Electronics, Inks and Coatings, Metal Packaging
Materials: Aluminum, Steel
The Compression Testing Machine consists of a base plate and steel cross head tightened by
With and tension rods. The hydraulic jack, inside the cover is fixed on the base plate. The lower platen rests centrally on the hydraulic jack. The lower platen can be removed and spacer can be placed on the hydraulic jack to reduce the gap between the upper and lower platens for smaller specimens.
The spacers are centrally located by means of centre locating pins. The lower platen canal then is kept on the spacer guided centrally by means of centre locating pins.
A screw passes through the cross head which can be raised or lowered to adjust the clearance
Between the two platens. The upper platens are attached to the lead screw. The upper platen has got spherical seat for the self-aligning action. A handle is attached to the adjustment screw for ease in operation. A cover is provided around hydraulic jack is prevent a no dust going inside the cylinder.
The motorized pumping unit is multiple plunger type. The pump is coupled to an electric motor
by means of V-belt and is housed in the cabinet. It has facility for
- Zero adjustment
- Peak value which is shown by pressing peak push button and it is retained till reset button is pressed.
- For fresh reading reset button should be pressed.
The slow fast knob is provided to control the flow rate which in turn control the rate of loading the electronic unit connected with the transducer.
Automatic cut off switch has been provided which will switch off the machine if in case load
exceeds the maximum load (for which the machine is designed)
The OFF-ON push button and the pressure release valve are mounted on the front panel for easy
operation. The rate of loading can be controlled by adjusting the knob valves.
A hand operated pump is also fixed inside the cabinet and is operated by inserting the handle in
the bracket thro the slot the pump may be operated in case the power supply fails during a test.
The unit is intended for use of 440 volts, 50 Hz. and 3 Phase supply. The main can be connected through the junction box.
1. One Digital Compression Testing Machine
2. One motorized pumping unit with Electronic display Unit.
3. One spacer
4. Tumblers Spanners
5. Hand Pump
6. Hydraulic Oil
7. Operating Instructions with G.A. Drawing.
- Mode of display 31⁄2 digits light emitting diode of 12.7 mm character height.
- Excitation supply to 5 volts DC regulated at 50 m. a Transducer
- Output connection 8 pins HCL locking connector
- Overall accuracy with ±1% of rating or better
- C. o/p. (Nominal) for 2 V DC for full scale reading of 1.999
- Safe operating temperature 10° to 45°c
- AC Power requirements 230 V. AC, ñ 10% main 50Hz Single phase.,
- Weight (nominal) 3.5 Kg.
- General Information Reading in excess of 1.999 will not be displayed and one of the following indication is obtained.
- Polarity Automatically sensed and displayed negative (-) Sign signifies tension load. Positive (+) sign or Absence of any sine signifies tension load.
- Decimal point The decimal point is automatically positioned.
- Sensing element : Point type strain gauge in full bridge configuration.
- Capacity : 100 Tonne.
- Maximum over load : 15 % of rated capacity.
- Device Linearity : ± 1 % of rated capacity.
- Hysterisis : ± 0.5% of rated capacity.
- Repeatability : ±0.2% of rated capacity.
- Terminal Resistance : 350 ohms nominal
- Excitation voltage : 5 volts D.C.
- Terminal connect : 8 Pins HCL locking connector
- Frequency Response : 0-50 Hz.
- Safe temperature : 10-50° C